Use of a cord suitable for outdoor use reduces the risk of electric shock. Ensure the switch is in the off-position before plugging in. Some examples of these chemicals are: •Crystalline silica from bricks and cement and other masonry products, and. Do not use any adapter plugs with earthed (grounded) power tools. Mostrar preguntas frecuentes ¡Haz tu pregunta! Twist the canister left or right and simply pull away from the tool (Fig. Appelez notre Service Hotline ou utilisez notre formulaire de contact. Vänligen kontrollerar inlämnade uppgifter. 11). Unplug the sander before changing accessories. WARNING a dust canister, empty it, frequently, after completion of sanding and before storing the sander. Produktdata kunde inte identifieras. For maximum efficiency, the dust canister should be emptied frequently during operation. 904 detailed instruction manuals and user guides of exploitation for Bosch. Keep your hair, clothing and gloves away from moving parts. Do not use sandpaper intended for larger sanding pads. To change accessory, peel protective sheet from the back of accessory. Compatible with: Bosch models: ROS10 (3601C87010) 5" Palm-Grip Random Orbit Sander, ROS20VS (3601C87511) 5" Variable Speed Palm-Grip Random Orbit Sander Kit, ROS20VSK (3601C87511) 5 in. all of the warnings listed below refers to your mains-operated (corded) power tool or batteryoperated (cordless) power tool. Do not throw sanding dust on an open fire. Knock excess dust out of the microfilter, or remove dust with your fingers or a soft brush. Keep cord away from heat, oil, sharp edges or moving parts. To avoid uneven results, do not skip more than one grit size when going from coarser to finer, and do not sand in one area for too long. 9). For most polishing, the soft backing pad will give the best results. 8). •Arsenic and chromium from chemicallytreated lumber. Many accidents are caused by poorly maintained power tools. Firmly push upward on tab on corner of lid, and remove from canister (Fig. In general, higher speeds will give the best results. cutting edges are less likely to bind and are easier to control. 7). Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. This symbol designates that this tool is listed by the Canadian Standards Association. ¿Tiene una pregunta sobre una herramienta, accesorio, aplicación o servicio?Llámenos al 1-877-BOSCH99 (1-877-267-2499) o visite las preguntas frecuentes. Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Proper interpretation of these symbols will allow you to operate the tool better and safer. This damper reduces the no-load speed, which helps prevent swirl marks on the workpiece surface and provides uniform finishing. Fullständig dokumentation finns för alla Bosch-produkter, vilket även inkluderar värdefull information om underhåll, reservdelar och hantering av mindre problem. To change the accessory, merely peel off the old accessory, remove dust from the pad if necessary, and press the new accessory in place (Fig. direkt om du behöver hjälp med information gällande din produkt. Your sander was designed to sand in small or confined areas. 11). If the surface is rough, begin with coarser grits and then complete the surfacing with medium and fine abrasives. Bosch ROS10 (3601C87010) 5" Palm-Grip Random Orbit Sander Parts. Avoid accidental starting. GFCI and personal protection devices like electrician’s rubber gloves and footwear will further enhance your personal safety. Properly maintained cutting tools with sharp. NOTE: For tool specifications refer to the nameplate on your tool. Align holes on backing pad with alignment posts and firmly tool push downward. IMPORTANT: Ring should not have bends or ripples when correctly seated. Be extremely careful of dust disposal, materials in fine particle form may be explosive. Electrolux. Här finns både till aktuella verktyg och till maskiner som inte längre finns på marknaden. This website or its third-party tools use cookies, which are necessary to its functioning and required to achieve the purposes illustrated in the cookie policy. If damaged, have the power tool repaired before use. Your sander is also equipped with a variable speed dial (Fig. BM 2609140467 08-07 8/28/07 8:54 AM Page 6, Functional Description and Specifications, Disconnect the plug from the power source before making any ! Distractions can cause you to lose control. This will ensure that the safety of the power tool is maintained. A moment of inattention while operating power tools may result in serious personal injury. The random orbit action is much like a powerful hand polishing action, and therefore does not have the high speeds at the edge of the pad which can burn the work surface. Before opening the dust canister lid, it is recommended to loosen dust from the microfilter dust canister by gently striking it against a solid surface (Fig. Manualer för kategorin Bosch Diskmaskiner. Vänligen försök igen eller skriv in E-Nr. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. Om du glömt var du lagt bruksanvisningen som levereras med produkten står vi till din tjänst. Open-coat aluminum oxide sanding discs are recommended for most wood or metal sanding applications, as this synthetic material cuts quickly and wears well. Proper interpretation of these symbols will allow you to operate the tool better and safer. Because the random orbit action is so effective, it is often possible to begin sanding with a medium grit disc and go directly to fine finishing. Clean the buffing pad and polishing bonnet with mild detergents and warm water. While the tool may appear to work, the electrical components of the AC rated tool are likely to fail and create a hazard to the operator. Sanding particles can be absorbed by your eyes and inhaled easily and may cause health complications. The random orbit sander is equipped with a backing pad of soft hardness, which is suitable for general service. Be sure to align the sanding disc holes with the holes in the backing pad to allow the dust extraction system to function. WARNING Read all instructions. this tool complies to NOM Mexican Standards. The optional carrying case is equipped with alignment posts that will allow you to easily align the holes in the sanding disc, with the holes in the backing pad. Such preventive safety. If you are experiencing premature wearout of the pad hooks, it may be due to pressure being applied to the tool during operation. 1). Some applications, such as plastics, glass, or stone require silicon carbide discs, which have a very sharp cutting edge. Combustion from. Do not wear loose clothing or jewelry. Holding the work by hand or against your body is unstable and may lead to loss of control. Liquids entering the motor housing is an electrical shock hazard. Keep children and bystanders away while operating a power tool. TO TURN THE TOOL "ON" depress the upper portion of the dust-protected switch to the number “I” position. To install dust canister: align dust port with hole in canister and push canister onto tool until it locks into place (Fig.